meet pico
A remarkably tiny
all-metal hot-end
for reprap 3D printers
capable of 500°c
in 3mm & 1.75mm

 Order Now

pico-reward-transparent



Where’s my Pico?

Pico Production Updates

an all metal hot-end for reprap 3D printers

engineered to solve common problems in 3d printing

Designed in Ohio. Made in the USA.

Battery Compare-01

Website-Body-Nozzles-01

Single Piece Body

Machined from a solid piece of 303 Stainless Steel

We wanted a design that does not suffer the same problems as traditional hot-ends.  So we aimed to reduce the number of components for the Pico hot-end—to one.  Beautifully machined to incredibly tight tolerances from a single piece of 303 stainless steel.  There is no PTFE (Teflon®) or PEEK to leak or fail.  In fact, we take leaks so serious, we designed a custom nozzle with chamfered edges to form a leak-free compression seal.

  • Reduced leak/failure points with only one conjunction
  • Heavyweight that is lightweight: 29g making it the lightest all-metal universal hot-end
  • Compact size: 56mm x 14.3mm dia. making it the smallest footprint of all-metal universal hot-ends
  • Meltdown-free, long-lasting, plastic-free design makes it strong and durable
  • Built-in 13mm wrench flats
  • Precision-machined 45 degree chamfered nozzles for a leak-resistant compression fit

Thermal-Magnified-LegendThermal Analysis

Thermally simulated, validated testing.

We ran exhaustive thermal studies to ensure the heat stays where it belongs.  To prevent jamming caused by heat migration upwards, the Pico has high-precision cooling fins—just 0.5mm thin.  The results speak for themselves; printing at 260°C the Pico’s top threads are a cool 45.9°C. The Pico is designed with a thermal break between the heat zone and the inlet.  So you can enjoy printing a variety of materials up to 300ºC or beyond¹.  *Some materials require active cooling ¹limited by thermistor to 300ºC

  • Stainless steel was chosen for thermal characteristics. It favors heat to just the heated portions as opposed to aluminum which absorbs heat throughout while reducing efficiency.
  • High-efficiency integrated vertical heater block. Threads inhibit heat transfer in threaded heater blocks
  • No bulky heat sink.
Heater-B3

Custom Made Heater

Tight tolerance. Made in the USA—in 12 or 24 volt

Going vertical allows an integrated heater block for a compact, beautiful design.  This improves the heating efficiency and boosts performance by uninhibited heat transfer vs. traditional threaded heater blocks.  The heater is placed in the optimal position to ensure even heating of the melt zone—not to mention a perfect-fit bore, it is neither too short or long—further increasing heater life.  And we did not want to use just any heater in Pico. We designed a custom heater, made in the USA to meet our specifications.  To top it off, it’s treated with a release agent in the rare case you need to change it out.

  • USA made heaters, tailored to our application, replace the sub-par imported heater cartridges
  • 40 Watts, 12 volts or 24 volts
  • High-temperature 25in DuraFlex® leads
  • 6.23mm diameter (¼in) by 20mm long    (+/- 0.04mm)

Web-Therm-Spring-2

100k Thermistor

Perfect placement. Kapton Tape Free.

We calculated the location of the thermistor based on function, not convenience.  The thermistor is the only component that controls the entire hot-end and through simulated and real-time temperature gradient maps—we found the sweet spot.  In-depth, the thermistor is located at the point where the temperature drop is realized first.  This allows your 3D printer to quickly react by turning the heater back on to ensure constant temperature within the melt zone.  What’s more, you will not find any kapton tape holding it in place — but a roll pin that is press fit into the Pico’s body.

  • We took out the guesswork with calculated positioning of the 100K thermistor for consistent true temperature readings
  • Internally-mounted thermistor with metal spring strain relief. No more messy kapton tape or cement.
  • 1 percent tolerance
  • Fully assembled 25in wire leads

Universal & Open Source

Power to the Maker!

The open source RepRap community has given us so much, and now it’s time we give back.  Once Pico is on the market, all our work will be available for anyone to download and use however they please.  Because when working together, we all move forward.  And thanks to this diverse community there are numerous variations of 3D printers out there.  So we designed mounts that will work with virtually any printer out there.

What’s inside the box

1 – 303 stainless steel single piece Pico body
1 – Brass nozzle in either 0.35, 0.4, 0.5 or 0.6mm
1 – 40-watt 6.23mm (¼in) x 20mm USA cartridge heater with 25in leads (12 or 24-volt)
1 – 100k thermistor fully assembled with 25in leads
1 – Mount (flat, groove, or groove for bowden)
1 – 40mm x 40mm x 10mm fan (12-volt)
1 – User manual

Pico hot-end:

  • 3mm or 1.75mm size filament hot-end
  • 303 stainless steel one-piece leak prevention structure
  • Single point M6x1.0 top mount
  • Interchangeable brass nozzle — M6 x1.0 (available in 0.35, 0.4, 0.5 & 0.6mm)
  • Interchangeable 40-watt 6.23mm (¼in) x 20mm USA cartridge heater with 25in leads (12 or 24-volt)—release agent coated
  • Interchangeable 100K NTC thermistor – 300°C Maximum—fully assembled. Heat shrink & Teflon tube insulated leads with metal spring strain relief
  • Eccentric 0.5mm thin Cooling Fins

Material: 303 stainless steel
Size: 47.6mm x 14.29mm diameter
Weight: 25.67 grams

Nozzle:

Material: Brass
Outlet Diameters: 0.35, 0.4, 0.5 & 0.6mm
Weight: 2.03 grams

Operating Temperature:

Up to 300º Celsius (572ºF)
*Limited by the thermistor

 

B3-Drawings-01